Construction Aggregate Calculator. Enter the width, length, thickness, and product density and hit the Calculate button to calculate your estimate. If you do not know the product density, use the optional density estimator or contact a local sales representative. Thickness Feetselect. Density LBSCubic Feetselect.
Get PriceTechnical Data Stone by location Unit Weight LbsFt Stone is also sold out of our three distribution yards, Gilmerton, Berkley and Toano. Please call for stone information. Test performed with Magnesium Sulfate MgSO Dense Graded refers to base, dust, crusher run How to compute approximate stone tonnages
Section 310Graded Aggregate Construction Page 5 310.4 Measurement A. Graded Aggregate Where specified for payment by the ton megagram, graded aggregate base, subbase or shoulder materials are measured in tons megagrams, mixed and accepted. When hauling material to the roadway, the actual weight of each loaded
Most pavers use 110 pounds per square yard per inch of thickness or 146.67 pounds pcf for estimating graded aggregate base. This seems to work well. Talk to your local quarry sales department. They should be able to give you densities for your region. Our quarries publish tables indicating compacted densities of all their products.
Divide Cubic Feet by 27 Cubic Yards. Multiply Cubic Yards by 1.5 Tons Needed. For figuring round areas, use the following example 24 ft round pool 4 deep. Start with 12 the radius 144 x 3.14 x depth divided by 27 x unit weight. x 3.14 452.16. x 1.5 8.30 tons. Depth Calculations.
If the volume is unit then, Bulk Density Mass. Unit in kgm 3 or lbft 3. In this definition, the volume is that contains both the aggregates and the voids between aggregates particles. The approximate bulk density of aggregate that is commonly used in normalweight concrete is between 12001750 kgm 3 75110 lbft 3. Here, the Standard test
A ratio of 12 or 13 HMA pavement depth to base aggregate dense depth. Example 5 inches of HMA pavement over 10 to 15 inches of base aggregate dense. When using base aggregate open graded, refer to FDM 14515. 10.2.3 DeepStrength or Perpetual HMA Pavements A standard 6inch base aggregate dense should be used.
Aggregate Base Weight is 1.92 tons per CY and their Recycled Aggregate Base is 1.89 per CY. The weight is pretty consistent. These products are checked once a year.
OGFC is more expensive per ton than densegraded HMA, but the unit weight of the mix when inplace is lower, which partially offsets the higher perton cost. The open gradation creates pores in the mix, which are essential to the mixs proper function therefore, anything that tends to clog these pores, such as lowspeed traffic, excessive
1 The department will pay for measured quantities at the contract unit price under the following bid items ITEM NUMBER DESCRIPTION UNIT 305.0110 Base Aggregate Dense 34Inch TON 305.0115 Base Aggregate Dense 34Inch CY 305.0120 Base Aggregate Dense 1 14Inch TON 305.0125 Base Aggregate Dense 1 14Inch CY
Construction Aggregate Calculator. Enter the width, length, thickness, and product density and hit the Calculate button to calculate your estimate. If you do not know the product density, use the optional density estimator or contact a local sales representative. Thickness Feetselect. Density LBSCubic Feetselect.
Section 902. AGGREGATES 902.01. General Requirements. The Department may reinspect and retest aggregates regardless of inspection at the producing plant. Provide safe access to the material for sampling from haul units or stockpiles. Do not use spent metal casting foundry sand, unless the contract expressly allows for its use.
Fine aggregate, often referred to as sand, screenings, or rock dust, is engineered for use in asphalt concrete, and select backfill, as well as many other construction applications. Size Range 31634 and Smaller Other DOT and Special Sizes Available. Base DenseGraded Base Coarse Aggregate base course is an engineered mixture of coarse and
5 Aggregate Specifications and Requirements Physical Quality Requirements Fine Aggregates Coarse Aggregates Aggregate Base Subbase Aggregate Pavement or Shoulders Summary of Gradation Requirements. 51 Absorption is expressed as a percentage of the dry weight. 53
Section 815Graded Aggregate Page 4 Ensure that the material does not contain delivery unit washout material. 3. Gradation Ensure that the finished product meets the quality and gradation requirements of Subsection 815.2.01 for Group II aggregates, except that the aggregate will be recycled concrete.
10112012 7 Road Aggregate 101 Nominal maximum andor minimum sized stone in mix The nominal size distribution of an aggregate specification is defined as the range of sieve openings through which 100 of the aggregate can pass. Road Aggregate 101 Gradation or distribution of different sized stones
Unit weight of a soil mass is the ratio of the total weight of soil to the total volume of soil. Unit Weight, g, is usually determined in the laboratory by measuring the weight and volume of a relatively undisturbed soil sample obtained from a brass unit weight of soil in the field may consist of a sand cone test, rubber balloon or nuclear densiometer.
Aggregate base materials Type I or II may be used in a stabilized or unstabilized form. c Crushed Hydraulic Cement Concrete shall not be used as Subbase or aggregate base material when any subsurface drainage system, such as standard underdrains UD4 or UD5 and or a stabilized open graded aggregate drainage layer OGDL is present, except
ii Abstract Cementtreated base CTB is a mixedinplace or centralplantproduced material consisting of soilaggregate, cement, and water that creates a strong and durable stabilized roadway base. This guide to CTB discusses its applications, benefits, design, construction, testing, and performance.
FTruck Body Pricing amp BrochuresExcelCubicYardageChart DCubicYardageChart D Rev A 692015 AGGREGATE TYPE
The most recent Aggregate Base Course ABC unit weight test results performed by the NCDOT MampT Soils lab can be queried using this page. Use the drop down boxes to select the company andor quarry submitting the sample. To see the results of all tests, click on the 34Search34 button without specifying a company or quarry.